Pleated Shades

Danville Pleated Shades From Danville Window Treatments

The light, cheap fold that isn't a cellular

Call (317) 854-7158Get Free Quote
Quick Answer

The questions below deal with specification rather than sales. Sizing, mount type, material choice and operation. Get those right and the aesthetic decisions take care of themselves.

  • Service: Pleated Shades for Danville homeowners
  • Service area: Danville, IN and surrounding areas
    • For a new order, plan on a measure appointment, then two to five weeks of fabrication, then an install visit. For a broken tilt gear or a dead battery, it's usually a single short visit and no waiting.
  • Insured and bonded
  • Serving Danville, IN since 2008
Pleated Shades Services

Expert Pleated Shades for Danville Homes

Pleated shades make sense in a specific corner of the Danville market. The town has 1,145 renter occupied units against 3,376 owner occupied, with a median gross rent of $1,151, and a landlord covering a whole unit is solving a different problem from an owner covering a front room. Pleated also fits where depth is short. The 640 houses Danville built in the 1970s carry the shallowest jambs in town, and one layer of pleated fabric stacks tighter than a honeycomb does. Add the 465 units from the 2010s where a secondary bedroom just needs covering, and there's a real place for this product.

What you're giving up is the air pocket. A cellular shade holds a honeycomb of trapped air in front of the glass, and Department of Energy work at Oak Ridge National Laboratory found cellular shades saved up to 20 percent of heating energy and up to 15 percent of total heating and cooling energy against a bare window. A pleated shade is one flat layer of folded fabric with no cell, so it doesn't carry that finding. In IECC Climate Zone 5A, where January averages a low of 20.9 degrees, that matters on the exterior wall of a 1970s Danville split level. Pleats also soften over years of raising.

When to Call

Signs You Need Pleated Shades

If you notice any of these in your Danville home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

A house needs every window covered before listing

An office window needs cover but not insulation

Cellular quotes came back higher than the room needs

Water was used to clean pleats and they relaxed

Trim is too shallow for a deeper headrail

A bonus room over the garage bakes in the afternoon

Route holes glow in a line after dark

An arched window has never been covered

The cord lock has to be reset every single morning

The shade creeps down an inch overnight, every night

Our Process

How Danville Window Treatments Handles Pleated Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Fabric opacity chosen

2

Three widths, three heights, diagonal

3

Written scope and total price

4

Custom fabrication, two to five weeks

5

Full travel run twice per unit

Real Project Photos

Pleated Shades in Danville

Photographs from real pleated shades jobs completed by our crew in Danville and surrounding areas.

Custom shades measured and installed in DanvillePlantation shutters fitted to a Danville windowCellular shades in a Danville living room
Scope of Work

What Pleated Shades Includes

Every Danville job is documented item by item. Here is what the crew covers.

The energy question answered honestly up front: a pleated shade is one layer of fabric with no cell behind it

Rooms steered to cellular instead wherever trapped air is the actual reason for the purchase

Rooms where pleated is the right call identified plainly, from secondary bedrooms to offices to a rental turnover

Pleat size set against the opening, a fine pleat on short glass and a larger pleat where the drop can carry it

Fabric opacity settled in writing before the order, light filtering against room darkening

Reflective backing considered on hard west and south exposures, described as what it is rather than as an energy rating

Three widths and three heights per opening with a diagonal check for square

Mounting depth read so the headrail sits inside the opening where an inside mount is what you want

Stack at the top measured against the glass, since a stacked pleated shade still covers the top few inches

Cordless lift specified in rooms children use, with products conforming to ANSI/WCMA A100.1-2022 for cord access

Route holes disclosed on any corded unit, because a closed pleated shade shows those holes as a line of small bright dots

Light gap per side written onto the paperwork, along with the 1/16 inch per side factory deduction Lutron publishes

Top-down bottom-up priced where a room wants daylight high and cover low

Arched, angled and fan-shaped openings templated on site, since pleated fabric is what those get built from

Wide spans reviewed for headrail deflection and split into two units where that is the right answer

Every opening in a room ordered on one purchase so the fabric comes off the same run

The paperwork done properly, with IC 24-5-11 requiring scope, dates and total price on residential jobs over $150

Bottom rail leveled and full travel run twice at every unit before we pack up

Pricing

What Pleated Shades Cost in Danville

National category figures put stock shades near $60 to $600 a window and custom-fabricated shades roughly $250 to $2,600. Those are published national ranges, not a price for any opening in Danville. Pleated sits low in the custom band and that is the honest appeal of it. One layer of fabric, a light headrail and a simple lift add up to less than a double cell shade with a blackout fabric and two lift systems. Where the number climbs is the same place it climbs on everything: width, drop, a room darkening fabric, a cordless lift on a heavy unit, or a templated arch that somebody has to build to a pattern. Danville Window Treatments prices from measured openings across Hendricks County rather than from a per-window average.

By Product

How Pleated Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

1 inch pleat: The standard and the one most rooms get. It holds a crisp horizontal line at ordinary window heights, it stacks small at the top, and it keeps the scale right on the bedroom and office windows this product usually goes into.

Fine pleat: A smaller fold for short windows, transoms and specialty shapes. More folds across the same drop means a finer face, and it's what a small arch or a narrow sidelight needs so the shape doesn't look coarse.

2 inch pleat: A larger fold that suits tall glass and big rooms, where a fine pleat across a long drop starts to read as texture rather than as a line. Fewer folds also means a slightly smaller stack for the same height.

Light filtering fabric: The everyday specification. Diffused daylight comes through, the view does not, and the room stays bright. It's the fabric that suits an office, a stairwell or any bedroom where waking up with the sun isn't a problem.

Room darkening fabric: A denser fabric that cuts most light through the face. It gets a bedroom dim rather than dark, since a pleated shade doesn't seal at the edges and an inside mount still passes light down both sides.

Reflective backing: A metallized back face that bounces some of the sun striking the shade back at the glass. It's a real property of the fabric and it's not an energy rating, and we describe it that way rather than putting a number on it.

Cordless spring lift: A spring lift with no operating cord on the product, and the version we specify in any room a child uses. It also removes the route holes from the conversation, since there's no lift cord passing through the fabric.

Corded lift with a cord lock: The traditional and least expensive control. The lift cord runs through holes punched in the pleats, which is exactly where a closed shade shows a vertical line of small bright dots at night. Worth knowing before you save the money.

Top-down bottom-up: Two rails on one shade, so the top can drop for daylight while the bottom stays up against a sidewalk. It adds a second lift system and its own hardware, which is where much of the extra cost comes from.

Fixed arch and angle-top units: A half-round, a quarter-round or an angled top built to a site template and left fixed. Pleated fabric is what these get made from, because a pleated fan holds its shape where a rolling product simply can't follow the geometry.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a Danville room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Pleated Shades FAQ

Questions we hear most often from Danville homeowners considering pleated shades.

Structure. A pleated shade is a single sheet of fabric folded into an accordion. A cellular is two sheets insured into honeycomb cells that hold air. From the room they look similar, and from an energy standpoint they aren't comparable: the Oak Ridge testing that produced the 20 percent heating figure was done on cellular, and none of it transfers to a pleated shade. Pleated stacks a little tighter and costs less. On an interior opening or a room you barely heat, that's a fair trade. On a bedroom wall facing a 20.9 degree January night, it isn't.
Often yes, and it's a legitimate use rather than a compromise. With 1,145 renter occupied units in town and a median gross rent of $1,151, a landlord is buying a covering that has to be replaceable at reasonable cost when a tenant leaves. Pleated does that. Specify cordless lift throughout, because you don't control who lives there and cord safety isn't negotiable in a unit you don't occupy. Inner cord non compliance is a substantial product hazard under 16 CFR 1120.3, which is a real federal rule and worth knowing if you own several units.
Better than most alternatives, which is the main structural argument for them. That 1970s stock is 640 units and it carries the shallowest mounting depth in Danville, plus aluminum slider frames with very little flat surface. A pleated headrail is slim and the stack at the top is tight, so it goes where a two inch faux wood blind or a double cell simply won't. We still check depth at three points, because a split level built in the middle of that decade has had fifty years of movement and the top of the opening rarely matches the bottom.
Not forever, and this is the wear pattern nobody mentions at the point of sale. Every raise compresses the folds and every lowering opens them, so after enough cycles the creases soften and the shade hangs with less definition than it did new. Sun accelerates it, and Northwood Haven has bare lots with no canopy where that exposure is at its worst anywhere in Danville. The effect is cosmetic rather than functional. If you want a shade that still looks factory crisp in fifteen years, a cellular holds its shape better and a shutter holds it indefinitely.
Yes, and it's one of the better applications for the feature. Danville's Main Street Historic District fronts US 36, so those 37 contributing houses take highway traffic past the front elevation all day, and dropping the top rail for daylight while the lower half stays covered is exactly right on a street facing room. The cost is hardware. Two lift paths means twice as many cords and stopping points that can go out of level, and a pleated shade doesn't have the body of a cellular to disguise a slight tilt. On a wide opening we'd think twice.
The same as any inside mount, and it's a manufacturing reality rather than a fitting error. Every custom shade is built narrower than its opening so it can operate, and Lutron publishes a standard factory deduction of 1/16 inch per side, with inside mount light gaps of 3/4 inch per side on their Roller 20/64. A pleated shade behaves similarly. If a dark room is the goal, an outside mount that overlaps the opening is a far cheaper fix than any fabric upgrade. We say this before the order rather than after the first sunny morning.
Structure. A pleated shade is a single layer of fabric folded into pleats, so when you look at the edge you see one accordion. A cellular shade is two layers joined so the folds form closed cells, and when you look at the edge you see honeycombs with air inside them. That trapped air is the entire point of a cellular shade. A pleated shade doesn't have it, which is why it costs less and why we don't make an energy argument for it.
Not the way a cellular does, and we won't pretend otherwise. Any fabric between you and cold glass in a Danville January does something, since it slows the air movement at the window and takes the edge off a draft you can feel from the couch. What it doesn't have is the trapped air pocket. The DOE and ORNL testing that gets quoted in this trade, up to 20 percent heating energy savings and up to 15 percent of total heating and cooling energy, was done on cellular shades. If that number is why you're buying, buy cellular.
When the room needs a good-looking shade rather than an energy product. Secondary bedrooms, home offices, hallways, a bonus room over a garage, a rental between tenants, a house being prepared for sale. All of those want something that fits the opening properly and costs sensibly. Pleated does that. It's also the right answer on arched and angled openings where no other product follows the shape, and that has nothing to do with budget.
Mostly, and they do soften. A pleated shade holds its folds because the fabric was heat-set at the factory, and that set relaxes slowly, faster on a hot window than on a shaded one. After several years on a west-facing Danville window you may see the folds sit slightly less sharp than they did, particularly at the bottom of the shade where it spends most of its life stacked. A cellular shade holds its shape longer because the cells brace each other. That's a real difference worth knowing.
Because the lift cord runs through holes punched in the fabric. On a corded pleated shade, each pleat has a small hole for the cord to pass through, and with the shade down those holes stack into a vertical line of bright dots that you notice at night and barely see during the day. It's construction, not damage. Cordless lift removes them entirely, since there's no cord passing through the fabric, and that's one of the better reasons to spend the difference.
In any room a child or a pet uses, yes, and we specify it that way. There's no operating cord on the product at all, which is the direction the ANSI/WCMA A100.1-2022 work on cord access points, and inner-cord non-compliance is treated as a substantial product hazard under 16 CFR 1120.3. On a pleated shade there's a second benefit, which is the route holes disappearing. The tradeoff is cost and the fact that a wide unit wants a hand at each end of the bottom rail rather than one in the middle.
Dim, not dark, and the reason is the edges rather than the fabric. A room darkening pleated fabric blocks most of the light through its face. What it can't do is close the gap down each side of an inside mount, and Lutron publishes 3/4 inch per side as a real inside-mount figure on their roller product to give you a sense of the scale. For a genuinely dark bedroom the answer is an outside mount with real overlap, or a blackout fabric running in side channels, which is a different product.
Yes, and pleated is usually what those get built from. A half-round over a front door, a quarter-round in a stairwell, an angled top following a vaulted ceiling: all of them get a site template, and the shade is fabricated as a fixed fan to that pattern. Fixed means it doesn't operate, which surprises people, so we say it early. If the shape has to move, the honest answer is often a movable shade below the straight line and a fixed unit above it.
Less than most products, and not nothing. A raised pleated shade gathers into a compact stack at the headrail, smaller than a double cell shade of the same height and much smaller than a woven natural. On a tall window that stack is a couple of inches of glass. On a short window it's a bigger share of the view, which is why we measure the drop and tell you where the bottom rail will actually sit when the shade is fully up.
Dust them and leave them alone otherwise. A vacuum on low with a brush head across the face, or a soft duster run along the folds, handles routine dirt. Spot marks come off with a barely damp cloth blotted, never rubbed hard, because the fabric is thin and the heat-set folds don't like being worked. Don't submerge them, and don't use a steamer on them. Fabric that has been soaked tends to come back with soft folds that never recover their line.
Reasonably, with the usual honesty about the exposure. A west or south window in Hendricks County takes real sun from late May into September, and a light colored pleated fabric there will soften in color over the years more than the same fabric on a north window. A reflective backing helps the fabric itself and improves how the shade looks from the street, since all the shades read the same color from outside. On the room behind it, NFRC puts UV at roughly 40 to 60 percent of fading damage, so the shade slows what happens to your floors. It doesn't end it.
Wide enough for most rooms, with weight and headrail deflection as the limits. Pleated fabric is light, so the fabric itself isn't the constraint. What matters is the headrail across a long span and the way a wide bottom rail behaves when you lift it from one end. Past the point where a single unit gets awkward, two shades sharing an opening reads better than one that drags. We work that out at the measure rather than after the box arrives.
Close, and possibly not exact. Pleated fabrics run in dye lots, so a shade woven this year can sit slightly off one woven three years ago. Across a hallway nobody sees it. On two windows in the same wall everybody does. The practical advice is to do a room in one order, even the small window you were going to skip. We write the fabric name and color onto your paperwork so a later order at least starts from the right reference.
Two to five weeks is the normal custom fabrication window, and pleated usually sits at the shorter end because it's a simple build. Templated arches and angle tops run longer, since somebody is making a one-off to your pattern. The window goes into your paperwork along with the scope, the dates and the total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Pleated Shades Across Danville

We measure and install in every one of these Danville neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in Danville

Danville Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in Danville

Poly slats for the rooms where real wood fails

Learn more →

Wood Blinds in Danville

Basswood stained to sit beside 1890s Danville trim

Learn more →

Vertical Blinds in Danville

Wide patio doors covered without blocking the traffic path

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in Danville

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
Danville, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 854-7158
Service area

Serving Danville and the surrounding area

Call NowGet Quote